5 Easy Steps to Remove the Charge Handle on an FN SCAR 17S * bigfinish.com

FN SCAR 17S Charge Handle Removal Overview

The FN SCAR 17S is a semi-automatic rifle that is known for its reliability and accuracy. It features a unique charging handle that is located on the left side of the receiver. The charging handle can be removed for cleaning, maintenance, or replacement.

To remove the charging handle, follow these steps:

Clear the weapon. Make sure that the weapon is unloaded and the chamber is empty.
Locate the charging handle. The charging handle is located on the left side of the receiver, just behind the ejection port.
Push the charging handle forward. This will disengage the charging handle from the bolt carrier.
Lift the charging handle up and out of the receiver. The charging handle can now be removed.

To reassemble the rifle, simply reverse the steps above.

Positioning the Charging Handle

The charging handle on the FN SCAR 17S can be positioned in three different ways: forward, neutral, and rearward. The forward position is used for charging the weapon. The neutral position is used for firing the weapon. The rearward position is used for locking the bolt open.

To position the charging handle, simply push it forward, neutral, or rearward until it clicks into place.

Position	Description
Forward	Used for charging the weapon
Neutral	Used for firing the weapon
Rearward	Used for locking the bolt open

Step 5: Inspecting the Charge Handle and Receiver

Once the charge handle is removed, thoroughly inspect it for any signs of wear, damage, or debris. Ensure that the handle moves smoothly and does not exhibit any excessive play or resistance. Examine the receiver where the charge handle was housed, paying attention to any potential deformities, scratches, or foreign objects that could interfere with the proper operation of the firearm.

Inspecting the Charge Handle and Receiver for Specific Points

Focus on the following key areas during the inspection:

Component	Points to Check
Charge Handle	– Surface wear or damage – Smoothness of movement – Excessive play or resistance – Presence of debris or obstructions
Receiver	– Deformities or scratches – Foreign objects or debris – Alignment with the charging handle track – Proper fit and function of the bolt carrier group

By paying close attention to these details, you can identify any potential issues that could affect the reliability and performance of your FN SCAR 17S. Promptly address any abnormalities or defects to ensure the firearm operates safely and effectively.

Step 6: Reinstalling the Charge Handle

1. Aligning the Charge Handle

* Grasp the angled portion of the charge handle and align it with the corresponding notch in the upper receiver.

2. Pivot the Charge Handle

* Gently pivot the charge handle upwards until it fully engages and locks into place.

3. Verifying Proper Installation

* Ensure that the charge handle can move freely and smoothly without any resistance.
* Check that the retaining pin is securely seated and does not protrude above the charge handle.

4. Depressing the Magazine Release

* Depress the magazine release button to release the empty magazine.

5. Inserting a New Magazine

* Insert a fully loaded magazine into the designated well until it locks securely into place.

6. Chambering a Round

* Pull back on the charging handle to chamber a round into the barrel.

7. Releasing the Charge Handle

* Release the charging handle to allow the bolt carrier group to fully enter the battery position.

8. Checking for Proper Function

* Cycle the action by pulling and releasing the charging handle several times to test its smooth operation.
* Ensure that the rifle ejects spent casings and chambers new rounds reliably.

9. Maintaining the Rifle

* Clean and lubricate the rifle regularly to maintain its reliability and longevity.
* Inspect the charge handle periodically for any signs of wear or damage and replace it if necessary.

Step	Description
1	Align the charge handle with the notch in the upper receiver.
2	Pivot the charge handle upwards until it locks into place.
3	Verify proper installation and movement.
4	Depress the magazine release button.
5	Insert a new magazine into the well.
6	Chamber a round into the barrel.
7	Release the charging handle to enter battery.
8	Cycle the action to test function and check for proper ejection and chambering.

Step 7: Closing the Upper Receiver

Now that the charging handle is removed, it’s time to close the upper receiver to reinstall the handguard and barrel nut. Here’s a detailed guide on how to do it:

9. Inspecting and Aligning Components

Before reassembling, thoroughly inspect all the components, including the upper receiver, handguard, and barrel nut. Ensure there are no visible defects or damage that could hinder proper functioning.

Next, align the handguard properly by inserting it into the upper receiver. Ensure the index marks on the handguard and receiver match to guarantee accurate alignment.

Component	Index Mark Location
Upper Receiver	Upper Rear Section
Handguard	Bottom Front Surface

Troubleshooting Common Issues

1. Failure to Extract Round

Ensure the magazine is properly inserted and seated. Inspect the extractor claw for damage or debris. Check the firing pin assembly for proper function and alignment.

2. Failure to Feed

Verify the magazine is loaded correctly and securely fastened. Check the feed ramp for obstructions or damage. Inspect the follower for any binding or deformation.

3. Double Feed

Examine the magazine spring for proper tension and damaged followers or lips. Check the extractor for any signs of wear or malfunction. Ensure the bolt is moving smoothly and not hesitating.

4. Failure to Eject Spent Casing

Check the ejector for any obstruction or damage. Inspect the extractor claw and spring for proper function and engagement with the spent casing.

5. Broken Charging Handle

Replace the broken charging handle with a new one. Ensure the latch mechanism is functioning correctly and not binding.

6. Failure to Lock Bolt Open

Inspect the bolt catch for any damage or debris. Check the magazine follower for proper engagement with the bolt catch.

7. Failure to Return Bolt to Battery

Ensure the gas system is functioning properly without any obstructions or leaks. Check the buffer spring and buffer for any damage or wear.

8. Excessive Recoil

Inspect the buffer and buffer spring for any signs of damage or wear. Check the gas system for proper function and adjust the gas regulator if necessary.

9. Poor Accuracy

Check the barrel for any damage or obstruction. Ensure the optics or iron sights are properly mounted and aligned. Inspect the bore for any fouling or obstruction.

10. Specific FN SCAR 17S Troubleshooting

Issue	Potential Cause	Solution
Failure to load multiple rounds on fresh magazine	Magazine spring tension too low	Replace magazine spring
Bolt carrier feels gritty and rough	Dry bolt carrier	Apply lubricant
Trigger pull feels heavy and inconsistent	Trigger spring worn or damaged	Replace trigger spring
Charging handle release button binds	Button spring weak or damaged	Replace button spring
Forward assist button stuck	Carbon buildup	Clean and lubricate

Fn Scar 17s How To Take Out Charge Handle

To remove the charging handle from an FN Scar 17s, follow these steps:

Unload the firearm and ensure it is safe.
Pull back on the charging handle to the rearmost position.
Locate the small button located on the right side of the upper receiver, just behind the charging handle.
Press the button and hold it down.
While holding the button down, pull the charging handle straight towards you to remove it from the upper receiver.
Once the charging handle is removed, you can clean or inspect it as needed.
To reassemble, simply insert the charging handle into the upper receiver and push it forward until it clicks into place.

5 Easy Steps to Remove the Charge Handle on an FN SCAR 17S