Mounting your Samsung monitor to its stand is a quick and easy process that can be completed in just a few minutes. By following these simple instructions, you can ensure that your monitor is securely attached and positioned at an optimal viewing angle.
The first step is to identify the type of mount that your monitor has. Samsung monitors typically come with either a round or square mount. Once you have identified the type of mount, locate the corresponding mounting bracket on the back of the monitor. The mounting bracket will have several holes that line up with the holes on the stand.
Next, align the mounting bracket with the stand and insert the screws into the holes. Tighten the screws until the monitor is securely attached to the stand. Once the monitor is attached, you can adjust the height and tilt of the monitor to achieve the most comfortable viewing position. The stand’s built-in swivel allows you to rotate the monitor from landscape to portrait orientation, providing maximum flexibility for your workspace.
Assembling the Stand’s Base
The first step in setting up your Samsung monitor is assembling the stand’s base. It’s a straightforward process that can be completed in a few minutes.
To begin, lay the stand flat on a stable surface. Then, locate the two screws that are attached to the bottom of the base.
| Step | Description |
|---|---|
| 1 | Take the base of the stand and remove the two screws from the bottom |
| 2 | Insert the stand’s mounting arm into the base from the middle back. |
| 3 | Secure the mounting arm to the base using the two screws that were removed earlier. |
| 4 | Turn the base over so that it is facing upwards. |
| 5 | Attach the monitor to the mounting arm by sliding it down from the top. |
| 6 | Secure the monitor to the mounting arm using the screws provided. |
Inserting the Vertical Arm into the Base
To insert the vertical arm into the base, follow these steps:
1. Remove the protective cover from the base.
Locate the protective cover on the base and remove it. The cover is usually held in place by screws or clips.
2. Orient the vertical arm and insert it into the base.
Orient the vertical arm so that the cable port is facing down. Align the vertical arm with the opening in the base and insert it.
To insert the vertical arm into the base:
- Hold the vertical arm with one hand and the base with the other hand.
- Align the grooves on the vertical arm with the rails inside the base.
- Slide the vertical arm into the base until it snaps into place.
- Tighten the screws or clips that secure the vertical arm to the base.
3. Reattach the protective cover.
Reattach the protective cover to the base. This will help to protect the vertical arm and the base from dust and damage.
| Step | Action |
|---|---|
| 1 | Remove the protective cover from the base. |
| 2 | Orient the vertical arm and insert it into the base. |
| 3 | Reattach the protective cover. |
Tightening the Screws to Secure the Stand
Once the stand is in place, it’s time to tighten the screws to secure it. Do not overtighten the screws, as this can damage the stand or the monitor. You should tighten the screws until they are just snug, then stop.
To tighten the screws, you will need the included wrench or a Phillips head screwdriver. Insert the wrench or screwdriver into the head of the screw and turn it clockwise to tighten. Be sure to tighten all four screws evenly. The tightening torque of the screws is 2.5-3.0 kgf.cm (24.5-29.4 in-lb).
If you are using a Phillips head screwdriver, be sure to use a screwdriver that is the correct size. Using a screwdriver that is too small can strip the screw head, making it difficult to remove the screw. If you are using a wrench, be sure to use a wrench that is the correct size. Using a wrench that is too large can damage the screw or the stand.
| Step | Description |
|---|---|
| 1 | Insert the wrench or screwdriver into the head of the screw. |
| 2 | Turn the wrench or screwdriver clockwise to tighten the screw. |
| 3 | Repeat steps 1 and 2 for the other three screws. |
Completing the Monitor Stand Assembly
Installing the Stand Base and Column
1. Align the base’s mounting groove with the column’s attachment point.
2. Slide the column into the base until it clicks into place.
Attaching the Head to the Column
3. Locate the screw hole on the back of the monitor head.
4. Screw the provided bolt into the hole.
5. Align the bolt with the hole on the top of the column.
6. Slide the head onto the column and tighten the screw.
Mounting the Monitor on the Stand
7. Mount the monitor onto the stand by aligning the mounting grooves on both sides.
8. Slide the monitor down until it clicks into place.
Adjusting the Monitor
9. Adjust the height, tilt, and swivel of the monitor as desired.
Using the Round Mount Adapter
10. If necessary, use the provided round mount adapter to attach the monitor to an existing stand or mounting arm.
10.1. For VESA-compatible stands, follow these steps:
10.2. For non-VESA-compatible stands, consult the manufacturer’s instructions.
| VESA-Compatible Stands | Non-VESA-Compatible Stands |
|—|—|
| – Attach the round mount adapter to the back of the monitor. | – Consult the manufacturer’s instructions. |
| – Tighten the screws to secure the adapter. | – Follow the specific mounting procedure provided. |
How To Attach Samsung Stand To The Monitor Round Mount
To attach the Samsung stand to the monitor’s round mount, you will need the following tools and materials:
– Samsung monitor with round mount
– Samsung stand
– Phillips head screwdriver
Follow these steps to attach the stand to the monitor:
1. Place the monitor face down on a soft surface, such as a towel or blanket.
2. Locate the four screws on the back of the monitor that secure the round mount.
3. Remove the screws using the Phillips head screwdriver.
4. Align the stand with the round mount on the back of the monitor.
5. Insert the screws into the holes on the stand and tighten them using the Phillips head screwdriver.
6. Flip the monitor over and place it on a flat surface.
7. Your Samsung stand is now attached to the monitor.
People Also Ask
How do I attach my Samsung monitor to the stand?
To attach your Samsung monitor to the stand, you will need to align the stand with the round mount on the back of the monitor and insert the screws into the holes on the stand and tighten them using the Phillips head screwdriver.
What type of screwdriver do I need to attach the Samsung stand to the monitor?
You will need a Phillips head screwdriver to attach the Samsung stand to the monitor.
Where can I find the screws to attach the Samsung stand to the monitor?
The screws to attach the Samsung stand to the monitor are located on the back of the monitor, securing the round mount.
