When your Fantech HP 2113 fan motor fails, it’s not just a matter of discomfort; it can also lead to health problems. Replacing the motor is a straightforward task that can be completed in under an hour with the right tools and materials. Follow these step-by-step instructions to get your fan up and running again in no time.
First, you’ll need to gather your tools and materials. You’ll need a new Fantech HP 2113 fan motor, a screwdriver, a wire cutter/stripper, and electrical tape. Once you have your tools and materials, you’re ready to begin.
To begin, turn off the power to the fan at the circuit breaker. Then, remove the front grille of the fan by unscrewing the screws that hold it in place. Once the grille is removed, you’ll have access to the fan motor. Disconnect the wires from the old motor and remove the mounting screws. Finally, install the new motor and reconnect the wires. Once the new motor is installed, turn on the power to the fan and test it to make sure it’s working properly.
Safety Precautions
- Turn Off the Power: Before attempting any work on the fan, it is crucial to ensure that the power source is disconnected. This means flipping the circuit breaker or removing the fuse associated with the fan. This eliminates the risk of electrical shock and makes the workspace safe.
To verify that the power is off, use a non-contact voltage tester to check the wires leading to the fan. Ensure that the tester indicates no voltage before proceeding.
Additionally, ensure that the fan is not spinning. If it is, allow it to come to a complete stop before starting work. This prevents injury from moving parts.
-
Wear Protective Gear: To minimize the risk of injury, equip yourself with appropriate protective gear before starting work. This includes safety glasses to shield your eyes from debris and loose parts, and gloves to protect your hands from sharp edges and electrical components.
-
Secure Access to the Fan: Ensure you have adequate access to the fan motor. If necessary, remove any obstructions or panels that block your path. Utilize ladders, stools, or platforms to reach the fan safely, ensuring stability and minimizing the risk of falls.
-
Prepare Tools and Materials: Before starting the replacement process, gather all the necessary tools and materials, including a new fan motor, screwdriver, wire cutters, electrical tape, and a voltage tester. Having everything organized and within reach streamlines the process and enhances safety.
Gathering Necessary Tools and Materials
Before embarking on the task of replacing your Fantech HP 2113 fan motor, it’s crucial to gather all the essential tools and materials. Here’s a comprehensive list to ensure you have everything at hand:
Tools:
| Screwdriver Set: | Includes Phillips and flathead screwdrivers in various sizes. |
|---|---|
| Adjustable Wrench: | Adjustable wrench to securely hold and loosen nuts and bolts. |
| Pry Bar: | Thin, flat tool to carefully pry apart components. |
| Measuring Tape: | To measure the dimensions of the fan motor and determine the correct replacement size. |
| Electrical Tester: | Optional but recommended to check electrical connections. |
Materials:
- Replacement fan motor: Ensure compatibility with the Fantech HP 2113 model.
- Electrical tape: To securely insulate electrical connections.
- Wire connectors: To connect the fan motor wires to the electrical system.
- Mounting screws: New screws to securely fasten the replacement fan motor.
- Anti-seize compound: Optional but highly recommended to prevent seizing and corrosion of bolts and nuts.
Disassembling the Fan Body
3. Removing the Motor
1. Once you have removed the screws, gently lift the front half of the fan body away from the back half. Be careful not to damage the wires attached to the motor.
2. Locate the two screws that hold the motor in place. These screws are usually located on the back of the motor.
3. Using a Phillips screwdriver, remove the two screws.
4. Carefully lift the motor out of the fan body. Be careful not to damage the wires attached to the motor.
Identifying the Motor
The Fantech HP 2113 fan motor is a 1/25 horsepower, 120-volt, single-phase motor. It has a black plastic housing and a round, metal end cap. The motor has two wires connected to it, a black wire and a white wire.
| Wire Color | Terminal |
| Black | L1 |
| White | L2 |
Removing the Old Fan Motor
Before you start, make sure to disconnect the power to the fan. You can do this by turning off the circuit breaker or removing the fuse that powers the fan.
Once the power is disconnected, you can start removing the old fan motor. Here are the steps:
- Remove the screws that hold the fan motor in place. The screws are usually located on the back of the fan motor.
- Once the screws are removed, you can pull the fan motor out of the fan housing. Be careful not to damage the wires when you are pulling the fan motor out.
- Disconnect the wires from the fan motor. The wires are usually connected to the fan motor with wire nuts. Twist the wire nuts counterclockwise to disconnect the wires.
- **Disconnect the capacitor (if any). If the fan is equipped with an additional capacitor, it would be cylindrical in shape and have two wires connected to it. Remove the wires by twisting the wire nuts (or unscrewing the terminals) counterclockwise. Use insulated pliers for this step, as the capacitor may still hold an electrical charge.**
- Once the wires are disconnected, you can remove the old fan motor from the fan housing.
Preparing the New Fan Motor
1. Inspect the Motor
Unpack the new motor and thoroughly inspect it for any damage. Check the bearings, housing, and electrical connections for any abnormalities or defects. If you notice any issues, contact the manufacturer or supplier immediately.
2. Clean the Motor Surface
Use a clean cloth dampened with isopropyl alcohol to gently wipe down the motor surface. This will remove any dirt, dust, or debris that may interfere with its performance or installation.
<3. Lubricate the Bearings (if necessary)
Some fan motors may come with pre-lubricated bearings. However, if the bearings require lubrication, use a high-quality bearing lubricant and apply it sparingly to the bearing surfaces.
4. Check the Electrical Connections
Verify that the electrical connections on the new motor match the existing wiring. Ensure that the terminals are clean and free of corrosion. If necessary, use a wire brush or sandpaper to clean the terminals before connecting the wires.
5. Detailed Inspection and Testing
| Component | Inspection Points | Testing |
|---|---|---|
| Bearings | Smooth rotation, no noise or vibration | Manual rotation to ensure smooth operation |
| Electrical connections | Secure and corrosion-free | VOM (Volt-Ohm Meter) continuity test |
| Housing | No cracks, damage, or deformation | Visual inspection |
| Impeller | Balance and alignment | Spin the impeller by hand to check for any wobble |
| Wiring | Correct gauge, insulation, and length | Visual inspection and continuity test |
Installing the New Fan Motor
With the wiring complete, it’s time to install the new fan motor. Begin by sliding the motor into the fan housing. Make sure the motor shaft is properly aligned with the fan blades.
6. Secure the Fan Motor
Secure the fan motor to the fan housing using the supplied bolts or screws. Tighten the bolts or screws evenly to ensure a secure fit. It is crucial to ensure that the motor is firmly fastened to prevent any vibrations or noise during operation.
| Tip | Description |
|---|---|
| Check Alignment | Before tightening the bolts or screws, re-check that the motor shaft is properly aligned with the fan blades. Misalignment can lead to vibrations and premature fan failure. |
| Use a Torque Wrench | For optimal tightening, use a torque wrench to apply the specified torque to the bolts or screws. This ensures the motor is securely fastened without overtightening. |
| Securely Tighten | Tighten the bolts or screws firmly, but avoid excessive force. Overtightening can damage the bolts or screw threads and compromise the fan’s safety. |
Once the fan motor is securely fastened, reconnect the electrical wires to the terminal block. Double-check the connections to ensure they are tight and secure.
Installing the Fan Motor
Once the new fan motor is in place, you can start reassembling the fan body. Begin by aligning the motor shaft with the impeller hub. Slide the impeller onto the shaft and tighten the set screw. Be sure to use a torque wrench to ensure that the set screw is properly tightened.
Connecting the Wires
Next, connect the wires from the fan motor to the terminal block. Match the wires according to their color and tighten the screws to secure the connections. Refer to the wiring diagram for guidance.
Inserting the Fan Blades
Once the wires are connected, insert the fan blades into the slots on the impeller. Align the blades with the corresponding slots and push them in until they snap into place. Make sure that the blades are securely seated.
Installing the Grill
Place the grill over the fan body and align the screw holes. Secure the grill using the screws provided.
Installing the Mounting Bracket
Attach the mounting bracket to the fan body using the bolts provided. The mounting bracket will allow you to mount the fan to a wall or ceiling.
Lubricating the Fan
In order to ensure smooth operation and longevity, lubricate the fan bearings. Apply a small amount of lithium-based grease to the bearings and rotate the impeller by hand to distribute the grease evenly.
Checking the Operation
Before mounting the fan, test it to make sure it is operating correctly. Connect the fan to a power source and turn it on. Listen for any unusual noises or vibrations. If everything sounds and feels normal, you can proceed with mounting the fan.
Electrical Wiring and Connections
The electrical wiring and connections for a Fantech HP 2113 fan motor are straightforward. Follow these steps to ensure a proper installation:
Step 1: Turn Off Power
Before starting any electrical work, always turn off the power to the fan at the circuit breaker or fuse box.
Step 2: Disconnect Old Wires
Locate the electrical box on the fan housing and remove the cover. Disconnect the wires connected to the old motor. Note the color of each wire and its corresponding terminal.
Step 3: Connect New Wires
Connect the wires from the new motor to the corresponding terminals in the electrical box. Use wire nuts to secure the connections and ensure a tight fit.
Step 4: Secure Wiring
Secure the wiring inside the electrical box using cable clamps or wire ties. This will prevent the wires from moving and potentially causing a short circuit.
Step 5: Grounding
Ensure that the green or bare wire coming from the motor is connected to the ground screw in the electrical box. This provides a safety measure by diverting any stray electrical current to the ground.
Step 6: Replace Cover
Replace the cover on the electrical box and secure it tightly.
Step 7: Test Motor
Turn on the power to the fan and check if the new motor is operating smoothly. If there is any noise or vibration, double-check your connections.
Step 8: Motor Specifications
The Fantech HP 2113 fan motor typically has the following specifications:
| Characteristic | Value |
|---|---|
| Voltage | 120 V AC |
| Power | 1/2 HP |
| RPM | 1140 |
| Frame Size | 56 |
Testing the Fan Motor
To test the fan motor, you will need a multimeter.
- Unplug the fan from the power source.
- Set the multimeter to the ohms setting.
- Touch the probes of the multimeter to the terminals of the fan motor.
- The multimeter should read a resistance of around 10 ohms.
- If the multimeter reads infinity, the fan motor is open.
- If the multimeter reads 0 ohms, the fan motor is shorted.
- If the multimeter reads a resistance of around 10 ohms, the fan motor is good.
Additional Information
The following table provides additional information about testing a fan motor:
| Fan Motor Test Results | |||
|---|---|---|---|
| Resistance | Open | Shorted | Good |
| Multimeter Reading | Infinity | 0 ohms | Around 10 ohms |
Troubleshooting
If you’re having trouble replacing your Fantech HP 2113 fan motor, there are a few things you can check:
- Make sure that the power to the fan is turned off.
- Check the wiring to make sure that it is properly connected.
- Inspect the fan motor for any damage.
If you’ve checked all of these things and you’re still having trouble, you may need to contact a qualified electrician for help.
Follow-Up Maintenance
Once you’ve replaced your Fantech HP 2113 fan motor, it’s important to perform regular maintenance to keep it running smoothly.
- Clean the fan blades and housing regularly to remove any dust or debris.
- Lubricate the fan motor bearings every six months.
- Check the fan belt for wear and tear, and replace it if necessary.
By following these simple maintenance tips, you can help extend the life of your Fantech HP 2113 fan motor.
10. Additional Maintenance Tips
In addition to the maintenance tips listed above, here are a few more things you can do to keep your Fantech HP 2113 fan motor running smoothly:
| Tip | Description |
|---|---|
| Use a surge protector | This will help protect your fan motor from power surges. |
| Don’t overload the fan | Make sure that the fan is not pulling too much air, as this can cause the motor to overheat. |
| Keep the area around the fan clean | Dust and debris can build up on the fan motor, which can cause it to overheat. |
How To Replace A Fantech Hp 2113 Fan Motor
Replacing a Fantech HP 2113 fan motor is a straightforward process that can be completed in a matter of minutes. By following the steps outlined below, you can ensure that your fan is up and running again in no time.
Step 1: Safety First
Before you begin, make sure to turn off the power to the fan at the circuit breaker or fuse box. This will prevent any electrical accidents from occurring.
Step 2: Remove the Fan Blade
Using a screwdriver, remove the screws that hold the fan blade in place. Once the screws are removed, carefully pull the fan blade straight off the motor shaft.
Step 3: Disconnect the Wiring
Locate the wiring harness that connects the fan motor to the power supply. Using pliers, carefully disconnect the wires from the motor terminals. Be sure to note which wire goes to which terminal so that you can reconnect them correctly later.
Step 4: Remove the Motor
Using a wrench, remove the bolts that hold the motor in place. Once the bolts are removed, you should be able to pull the motor straight out of the housing.
Step 5: Install the New Motor
Insert the new motor into the housing and secure it in place with the bolts. Be sure to tighten the bolts until they are snug, but do not overtighten them.
Step 6: Reconnect the Wiring
Reconnect the wires to the motor terminals, making sure that each wire goes to the correct terminal. Secure the wires in place with the wire nuts.
Step 7: Install the Fan Blade
Slide the fan blade onto the motor shaft and secure it in place with the screws. Be sure to tighten the screws until they are snug, but do not overtighten them.
Step 8: Turn on the Power
Turn on the power to the fan at the circuit breaker or fuse box. The fan should now be up and running again.
People Also Ask About How To Replace A Fantech Hp 2113 Fan Motor
How do I know if my Fantech HP 2113 fan motor is bad?
There are a few signs that can indicate that your Fantech HP 2113 fan motor is bad. These include:
- The fan is making a loud noise.
- The fan is not moving air as well as it used to.
- The fan is overheating.
- The fan is not turning on.
Can I replace the fan motor myself?
Yes, you can replace the fan motor yourself. However, if you are not comfortable working with electrical devices, it is best to hire a qualified electrician to do the job.
How much does it cost to replace a Fantech HP 2113 fan motor?
The cost of replacing a Fantech HP 2113 fan motor will vary depending on the cost of the motor itself and the labor costs of the electrician. However, you can expect to pay between $100 and $200 for the entire job.
